etckeeper/openzwave/popp/701202.xml

<Product Revision="1" xmlns="https://github.com/OpenZWave/open-zwave">
  <MetaData>
    <MetaDataItem name="Name">Mold Detector</MetaDataItem>
    <MetaDataItem name="Description">
	This device measures the three air quality parameters temperature, humidity and dew point and reports them to a central controller. Beside this, the device can directly control groups of other Z-Wave devices on over- and undershooting a set temperature and/or humidity parameter. This can be used to establish control loops for temperature and humidity. The device wakes up every 15 minutes to measure the values and it will send unsolicited reports when values change, Additionally the device will report all values request on.
	The mold detector is actively monitoring the danger of mold in a room based on the temperature and humidity and will issue alarm warnings when critical air conditions are met. Wireless Alarm and red and a green blinking LED will indicate a mold condition. This local LED warning function is also available when the device is not included in any Z-Wave network and works stand alone.
    </MetaDataItem>
    <MetaDataItem name="OzwInfoPage">http://www.openzwave.com/device-database/0154:0014:0004</MetaDataItem>
    <MetaDataItem name="ProductPage">https://popp.eu/products/sensors/mold-detector-701202/</MetaDataItem>
    <MetaDataItem name="ProductSupport">https://popp.eu/support/</MetaDataItem>
    <MetaDataItem name="ProductPic">images/popp/701202.png</MetaDataItem>
    <MetaDataItem name="ProductManual">https://manuals.zwave.eu/backend/make.php?lang=EN&amp;sku=POPE701202&amp;cert=</MetaDataItem>
    <MetaDataItem name="WakeupDescription">Press the tamper button on the side of the appliance once.</MetaDataItem>
    <MetaDataItem name="InclusionDescription">
	1. Open the housing.
	2. Remove the battery protection.
	3. Press the tamper button on the side of the appliance three times quickly.</MetaDataItem>
    <MetaDataItem name="ExclusionDescription">
	1. Open the housing.
	2. Press the tamper button on the side of the appliance three times quickly.
    </MetaDataItem>
    <MetaDataItem name="ResetDescription">
	Remove the cover, press the button for 5 seconds until it flashes green. Release the button and press the button again until the blinking stops.
    </MetaDataItem>
    <!-- ZWProductPage refers to a similar device with a difference product number but with the same certification ID (ZC10-19026384) -->
    <MetaDataItem id="0014" name="ZWProductPage" type="0004">https://products.z-wavealliance.org/products/3249?selectedFrequencyId=1</MetaDataItem>
    <MetaDataItem id="0014" name="FrequencyName" type="0004">CEPT (Europe)</MetaDataItem>
    <MetaDataItem id="0014" name="Identifier" type="0004">701202</MetaDataItem>
    <ChangeLog>
      <Entry author="Jan Coolen - jan@coolen.pt" date="01 March 2019" revision="1">
	Initial configuration file, based on information from the vendor's and z-wavealliance.org websites, but with small linguistic changes and a few  corrections.
      </Entry>
    </ChangeLog>
  </MetaData>
  <!-- Configuration Command Class -->
  <CommandClass id="112">
    <Value genre="config" index="1" label="Minimum Temperature change to report" max="100" min="0" type="byte" units="1/10 degree" value="20">
      <Help>
	This value defines the minimum change of temperature to cause an unsolicited report of humidity to the central controller using Lifeline.
	If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 4, may still be active. 
	Default Value: 20
      </Help>
    </Value>
    <Value genre="config" index="2" label="Minimum humidity change to report" max="20" min="0" type="byte" units="%" value="7">
      <Help>
	This value defines the minimum change of humidity to cause an unsolicited report of humidity to the central controller using Lifeline.
	If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 4, may still be active.
	Default value: 7
      </Help>
    </Value>
   <!-- Not sure whether in the next setting max value is correct. Should be 900-65535 or 0 -->
   <Value genre="config" index="4" label="Periodic Reports" max="65536" min="900" type="short" units="seconds" value="43200">
      <Help>
	This parameter defines the time interval to send an unsolicited report.
	If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 1 and 2, may still be active.
	Default value: 43200
      </Help>
    </Value>
   <Value genre="config" index="5" label="Temperature Upper Watermark value" max="1000" min="0" type="short" units="1/10 degrees" value="0">
      <Help>
	This parameter defines a temperature. If the measured temperature surpasses this watermark a BASIC command is sent into Association Group 2
	Default Value: 0
      </Help>
    </Value>
   <Value genre="config" index="6" label="Temperature Lower Watermark value" max="1000" min="653356" type="short" units="1/10 degrees" value="0">
      <Help>
	This parameter defines a temperature. If the measured temperature drops below this watermark a BASIC command is sent into Association Group 3
	Default Value: 0
      </Help>
    </Value>
   <Value genre="config" index="7" label="Humidity Upper Watermark value" max="100" min="0" type="byte" units="%" value="0">
      <Help>
	This parameter defines a relative humidity. If the measured relative humidity surpasses this watermark a BASIC command is sent into Association Group 4
	Default Value: 0
      </Help>
    </Value>
   <Value genre="config" index="8" label="Humidity Lower Watermark value" max="90" min="0" type="byte" units="%" value="0">
      <Help>
	This parameter defines a relative humidity. If the measured relative humidity drops below this relative humidity a BASIC command is sent into Association Group 5 
	Default Value: 0
      </Help>
    </Value>
   <Value genre="config" index="9" label="Low Temperature Trigger BASIC Set Command Value" max="255" min="0" type="byte" units="" value="255">
      <Help>
	This defines what BASIC command shall be sent out into association group 3 
	Default Value: 255
      </Help>
    </Value>
   <Value genre="config" index="10" label="High Temperature Trigger BASIC Set Command Value" max="255" min="0" type="byte" units="" value="0">
      <Help>
	This defines what BASIC command shall be sent out into association group 2 
	Default Value: 0
      </Help>
    </Value>
   <Value genre="config" index="11" label="Low Humidity Trigger BASIC Set Command Value" max="255" min="0" type="byte" units="" value="255">
      <Help>
	This defines what BASIC command shall be sent out into association group 5 
	Default Value: 255
      </Help>
    </Value>
   <Value genre="config" index="12" label="High Humidity Trigger BASIC Set Command Value" max="255" min="0" type="byte" units="" value="0">
      <Help>
	This defines what BASIC command shall be sent out into association group 4 
	Default Value: 0
      </Help>
    </Value>
  </CommandClass>
  <!-- The Association Group Information -->
  <CommandClass id="133">
    <Associations num_groups="5">
      <Group index="1" label="LifeLine" max_associations="5"/>
      <Group index="2" label="Temperature High Trigger" max_associations="5"/>
      <Group index="3" label="Temperature Low Trigger" max_associations="5"/>
      <Group index="4" label="Humidity High Trigger" max_associations="5"/>
      <Group index="5" label="Humidity Low Trigger" max_associations="5"/>
    </Associations>
  </CommandClass>
</Product>