etckeeper/openzwave/devolo/mt2761.xml

<Product Revision="1" xmlns="https://github.com/OpenZWave/open-zwave">
  <MetaData>
    <MetaDataItem name="OzwInfoPage">http://www.openzwave.com/device-database/0175:0052:0003</MetaDataItem>
    <MetaDataItem name="ProductPic">images/devolo/mt2761.png</MetaDataItem>
    <MetaDataItem id="0052" name="ZWProductPage" type="0003">https://products.z-wavealliance.org/products/2962/</MetaDataItem>
    <MetaDataItem name="InclusionDescription">•	Connect module to power supply (with 
temperature sensor connected - if purchased),
•	auto-inclusion (works for about 5 seconds after connected to power supply) or
•	press push button I1 three times within 3s (3 times change switch state within 3 seconds) or
•	press service button S (only applicable for 24 V SELV supply voltage) for more than 2 second.

NOTE1: For auto-inclusion procedure, first set main controller into inclusion mode and then connect module to power supply.

NOTE2: When connecting temperature sensor to module that has already been included, you have to exclude module first. Switch off power supply, connect the sensor and re-include the module.
</MetaDataItem>
    <MetaDataItem name="ExclusionDescription">•	Connect module to power supply 
•	bring module within maximum 1 meter (3 feet) of the main controller,
•	enable add/remove mode on main controller,
•	press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or
•	press service button S (only applicable for 24 V SELV supply voltage)  for more than 6 second.
By this function all parameters of the module are set to default values and own ID is deleted.

If push button I1 is pressed three times within 3s (or service button S is pressed more than 2 and less than 6 seconds) module is excluded, but configuration parameters are not set to default values. 

NOTE: Please use this procedure only when the network primary controller is missing or otherwise inoperable.

NOTE: If the module is included with parameters 71 with value different to default and module reset is done, wait at least 30s before next inclusion
</MetaDataItem>
    <MetaDataItem name="ResetDescription">•	press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or
•	press service button S (only applicable for 24 V SELV supply voltage)  for more than 6 second.

NOTE: Please use this procedure only when the network primary controller is missing or otherwise inoperable.
</MetaDataItem>
    <MetaDataItem name="Description">This Z-Wave module is used to control the motor of blinds, rollers, shades, venetian blinds, etc … The module can be controlled either through a Z-Wave network or through the wall switch. Precise positioning is supported for motors equipped with mechanical or electronic end switches. The module is designed to be mounted inside a “flush mounting box”, hidden behind a traditional wall switch. Module measures power consumption of motor and support connection of digital temperature sensor. It is designed to act as repeater in order to improve range and stability of Z-Wave network.                      
</MetaDataItem>
    <MetaDataItem name="ProductManual">https://products.z-wavealliance.org/ProductManual/File?folder=&amp;filename=MarketCertificationFiles/2962/Manual_Devolo_HC Shutter_FM.pdf</MetaDataItem>
    <MetaDataItem id="0052" name="Identifier" type="0003">MT2761</MetaDataItem>
    <MetaDataItem name="Name">Home Control Shutter FM</MetaDataItem>
    <MetaDataItem id="0052" name="FrequencyName" type="0003">CEPT (Europe) / Australia / New Zealand / U.S. / Canada / Mexico</MetaDataItem>
    <ChangeLog>
      <Entry author="github.com/ProtoFoo" date="04 May 2020" revision="1">Initial Version - Copied from qubino/ZMNHCDx.xml</Entry>
    </ChangeLog>
  </MetaData>

  <CommandClass id="112">
    <Value genre="config" index="10" instance="1" label="Activate / deactivate functions ALL ON/ALL OFF" max="255" min="0" size="2" type="list" value="255">
      <Help>Flush 1 relay module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.</Help>
      <Item label="ALL ON active, ALL OFF active" value="255"/>
      <Item label="ALL ON is not active ALL OFF is not active" value="0"/>
      <Item label="ALL ON is not active ALL OFF active" value="1"/>
      <Item label="ALL ON active ALL OFF is not active" value="2"/>
    </Value>
    <Value genre="config" index="40" instance="1" label="Power reporting in Watts on power change for Q1 or Q2" max="100" min="0" size="1" type="byte" units="%" value="1">
      <Help>Set value from 0 - 100 (0% - 100%). 0 - Reporting Disabled. 1 - 100 = 1% - 100% Reporting enabled. Power report is send (push) only when actual power (in Watts) in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%. Default value 1</Help>
    </Value>
    <Value genre="config" index="42" instance="1" label="Power reporting in Watts by time interval for Q1 or Q2" max="65535" min="0" type="short" units="s" value="300">
      <Help>Set value means time interval (0 - 65535) in seconds, when power report is send. 0 - Reporting Disabled. 1 - 65535 = 1second - 65535 seconds. Reporting enabled. Power report is send with time interval set by entered value. Default value 300 (power report in Watts is send each 300s)</Help>
    </Value>
    <Value genre="config" index="71" instance="1" label="Operating modes" max="1" min="0" size="1" type="list" value="0">
      <Help>This parameter defines selection between two available operating modes</Help>
      <Item label="Shutter mode" value="0"/>
      <Item label="Venetian mode (up/down and slate rotation)" value="1"/>
    </Value>
    <Value genre="config" index="72" instance="1" label="Slats tilting full turn time" max="65535" min="0" type="short" units="s" value="150">
      <Help>
				This parameter defines the time necessary for slats to make full turn (180 degrees)
				default value 150 = 1,5 seconds
				0 - Tilting time disabled
				1 - 32767 = 0,01seconds - 327,67 seconds
				</Help>
    </Value>
    <Value genre="config" index="73" instance="1" label="Slats position" max="1" min="0" size="1" type="list" value="1">
      <Help>This parameter defines slats position after up/down movement through Z-wave or push-buttons
				Slats return to previously set position only in case of
				</Help>
      <Item label="Z-wave control" value="0"/>
      <Item label="Z-wave control, push-button operation or when the lower limit switch is reached" value="1"/>
    </Value>
    <Value genre="config" index="74" instance="1" label="Motor moving up/down time" max="65535" min="0" type="short" value="0">
      <Help>This parameter defines shutter motor moving time of complete opening or complete closing.
				Default value 0
				0 - moving time disabled (working with limit switches).
				1 - 65535 = 0,1seconds - 6553,5seconds
				After that time motor is stopped (relay goes to off state)</Help>
    </Value>
    <Value genre="config" index="76" instance="1" label="Motor operation detection" max="127" min="0" type="byte" units="w" value="10">
      <Help>
				Power threshold to be interpreted when motor reach the limit switch.
				default value 10 = 10W
				0 - 127 = 1-127 W. The value 0 means reaching a limit switch will not be detected.
			</Help>
    </Value>
    <Value genre="config" index="78" instance="1" label="Forced Shutter calibration" max="1" min="0" size="1" type="list" value="0">
      <Help>By modifying the parameters setting from 0 to 1 a Shutter enters the calibration mode</Help>
      <Item label="Default" value="0"/>
      <Item label="Start calibration process" value="1"/>
    </Value>
    <Value genre="config" index="85" instance="1" label="Power consumption max delay time" max="50" min="0" type="byte" units="" value="0">
      <Help>
				This parameter defines the max time before motor power consumption is read after one of the relays is switched ON.
				If there is no power consumption during this max time (motor not connected, damaged or requires higher time to start, motor in end position) the relay will switch OFF.
				Time is defined by entering it manually.
				default value 0 = time is set automatically
				3 - 50 = 0,3seconds - 5seconds (100ms resolution)
				</Help>
    </Value>
    <Value genre="config" index="90" instance="1" label="Time delay for next motor movement" max="30" min="1" type="byte" units="" value="5">
      <Help>
				This parameter defines the minimum time delay between next motor movement (minimum time between switching motor off and on again).
				default value 5 = 500ms
				1 - 30 = 0,1seconds - 3seconds (100ms resolution)
				</Help>
    </Value>
    <Value genre="config" index="110" instance="1" label="Temperature sensor offset settings" max="65535" min="1" type="short" value="32536">
      <Help>
				Set value is added or subtracted to actual measured value by sensor.
				default value 32536
				32536 - offset is 0.0C
				From 1 to 100 - value from 0.1 C to 10.0 C is added to actual measured temperature.
				From 1001 to 1100 - value from -0.1 C to -10.0 C is subtracted to actual measured temperature.
			</Help>
    </Value>
    <Value genre="config" index="120" instance="1" label="Digital temperature sensor reporting" max="127" min="0" type="byte" units="" value="5">
      <Help>
				If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter
				default value 5 = 0,5C
				0 - Reporting disabled
				1-127 = 0,1C - 12,7C, step is 0,1C
				</Help>
    </Value>
  </CommandClass>
  <!-- Association Groups -->
  <CommandClass id="133">
    <Associations num_groups="9">
      <Group index="1" label="Lifeline" max_associations="1"/>
      <Group index="2" label="basic on/off (triggered at change of the input I1 state and reflecting its state)" max_associations="16"/>
      <Group index="3" label="basic on/off (triggered at change of the input I2 state and reflecting its state)" max_associations="16"/>
      <Group index="4" label="basic on/off (triggered at sensing moving direction of roller: up=FF, down=0)" max_associations="16"/>
      <Group index="5" label="basic on/off (triggered at reaching roller position: bottom=FF, top=0)" max_associations="16"/>
      <Group index="6" label="basic on/off (triggered at reaching roller position: bottom=FF, not bottom=0)" max_associations="16"/>
      <Group index="7" label="multilevel set (triggered at changes of value of the Flush shutter DC position)" max_associations="16"/>
      <Group index="8" label="multilevel set (triggered at changes of value of slats tilting position)" max_associations="16"/>
      <Group index="9" label="multilevel sensor report (triggered at change of temperature sensor)" max_associations="16"/>
    </Associations>
  </CommandClass>
  <!-- Remove COMMAND_CLASS_BASIC -->
  <CommandClass action="remove" id="32"/>
  <!-- Map endpoints to instances -->
  <CommandClass id="96">
    <Compatibility>
      <MapRootToEndpoint>true</MapRootToEndpoint>
    </Compatibility>
  </CommandClass>
</Product>