http://www.openzwave.com/device-database/0086:004B:0003 images/aeotec/zw075.png https://products.z-wavealliance.org/products/1045/ N/A Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Action button that you can find on the product's housing. CEPT (Europe) Smart Switch Gen5 Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable. Aeon Labs Smart Switch Gen5 is a Z-Wave device that can report the wattage energy usage and KWH usage to a Z-Wave Controller (especially a gateway), it can be controlled by other Z-Wave devices to turn on/off loads, it can bear up to 16A current of resistive loads. It also acts as a repeater that forwards Z-Wave command messages to destination nodes if the originating controller is out of range from the destination node. By taking advantage of the Z-Wave mesh network, commands can be routed to their destination via intermediary “listening” Z-Wave products. Products that are Z-Wave certified can be used and communicate with other Z-Wave certified devices. Also a tool that can be programmed, scheduled, controlled and communicated with from anywhere in the world. Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Action button that you can find on the product's housing. ZW075-C16 https://Products.Z-WaveAlliance.org/ProductManual/File?folder=&filename=Manuals/1056/Aeon Labs Smart Switch Gen5_Update 2.pdf Initial Metadata Import from Z-Wave Alliance Database - https://products.z-wavealliance.org/products/1045/xml Updated Metadata Import from Z-Wave Alliance Database - https://products.z-wavealliance.org/products/1053/xml Updated Metadata Import from Z-Wave Alliance Database - https://products.z-wavealliance.org/products/1056/xml https://products.z-wavealliance.org/products/1053/ ZW075-A02 U.S. / Canada / Mexico https://products.z-wavealliance.org/products/1056/ Australia / New Zealand ZW075-B09 Configuration Value 1: 1-255 Configuration Value 1 is to Specify the time that Smart Switch need blink, The unit is Second; Configuration Value 2: 1-255 Configuration Value 2 is to Specify the Cycle of on/off, the unit of it is 0.1 second. Load will be closed when the Current overruns (EU 16.2A) for more than 2 minutes Configure the output load status after re-power on. Defines the automated status notification of an associated device when status changes Enable/disable Wattage threshold and percent. The value represents the minimum change in wattage for a Report to be sent (default 25 W) The value represents the minimum percentage change in wattage for a Report to be sent (Default 5) Set report types for groups 1, 2 and 3 to default. Defines the type of report sent for reporting group 1. 1 is meter report for voltage. 2 is meter report for current. 4 is meter report for watts. 8 is meter report for kilowatts. Value 1 (msb) Reserved Value 2 Reserved Value 3 Reserved Value 4 (lsb) bits 7-4 reserved bit 3 kWh bit 2 watt bit 1 current bit 0 voltage Defines the type of report sent for reporting group 2. 1 is meter report for voltage. 2 is meter report for current. 4 is meter report for watts. 8 is meter report for kilowatts. Value 1 (msb) Reserved Value 2 Reserved Value 3 Reserved Value 4 (lsb) bits 7-4 reserved bit 3 kWh bit 2 watt bit 1 current bit 0 voltage Defines the type of report sent for reporting group 3. 1 is meter report for voltage. 2 is meter report for current. 4 is meter report for watts. 8 is meter report for kilowatts. Value 1 (msb) Reserved Value 2 Reserved Value 3 Reserved Value 4 (lsb) bits 7-4 reserved bit 3 kWh bit 2 watt bit 1 current bit 0 voltage Set time interval for sending reports for groups 1, 2 and 3 to default. Defines the time interval when the defined report for group 1 is sent. Defines the time interval when the defined report for group 2 is sent. Defines the time interval when the defined report for group 3 is sent. Partner ID Enable/disable Configuration Locked Device tag. Reset to the default configuration.